How to reset oasis washer Videos

Good info.

Hi Bill, very informative. Thank you. Upon tilting down the unit a 2" brass pin, with one side flat, fell out. I can't find anywhere on the unit's diagram where it may came from. Any ideas?

Bill, my Kenmore 90 series ( I love this machine…) wasn't spinning right, made screeching noise, found the C-ring in the bottom of the clutch, kept falling down after being replaced. Now trying to replace the drive & brake assembly, can't get the assembly to come out. Tried hitting on the tabs on the drive tube to make the assembly come loose. No can do. Is it possible the metal vase-like neck on the inner basket, the drive block, and the shaft of the d&b assembly are fused together? They just will not separate from each other. Ever run into this problem? Urrgh. Thanks, Myra

Just wondering if i should replace both the motor coupler and the clutch? not sure which one is bad. My whirlpool washer spins when there is no clothes in it but when there is a load in it it doesnt spin.

Hi Bill, help please...I watched your video and the cuppler was good so I took it apart to check the clutch and that is not broke either. What do I do now? prior to taking apart my machine stopped working on spin cycle due to uneven load, afterwards I couldn't get it to spin or rinse.

just put a zip tie my friend and save your customer some money.

total thumbs up !! with the help of your video, able to discover my flapper was broken.. Not so bad I cannot fix... got it all out and is one the mend as I type!! show me how it is done and this little gal with cancer can, oh so do!! THANK YOUever so much

i reset the motor on mine, and it works ok on an empty load. when there is laundry in there, it makes it to the end of the rinse cycle but will not spin out. i hear a bunch of clicking sounds but nothing.

i installed new coupler, still have the same problem. it does spin when i spin it with my hand but stops shortly after. soes this sound familiar

Question when the machine doesn't spin dry the clothes how do I fix that 

I just want to know why are you and people like you this nice? thank you for being so nice...

I have a Maytag Bravo washer Mod#MVWB300WQ1. The wash cycle will start out fine and the somewhere through the cycle it stops and I get a flashing "Ld" error code and the lid unlocks. When I press the power button , the screen changes fro "Ld" to 25. I then press the start button,the lid locks but all I get is a gurgling sound for a while. I unplug it and attempt to reboot the computer. The time unplugged varies because in the past I had to do this procedure several times, and eventually,so far it will continue the wash ,rinse and spin cycle. I had a Sears repairman out the other day and unfortunately I couldn't repeat the problem and couldn't remember the error code and he checked it out but obviously he couldn't fix the problem.

Good morning! After being quoted $500 to replace my control board on my Cabrio Washer, I have decided to replace it myself. Question: The backside of my Cabrio model WTW5460XW0 does not look like the above video, which is super easy. It has metal plates with some hex screws and flathead screws. Do you have instructions on how to remove this panel so I can replace the board? Thanks!

This video says it's the control board right from the get go, but other videos say check the water control hose or housing, before replacing the whole control board. So is that the right thing to check before going a head and replacing and spending the money for control board? 

Will the control board determine if the washer starts at all? Thanks.

I fully agree with Louis Small's post below. I have had this F1 error code happen 2 times, (1st a year ago), then again tonight. I fixed it by simply blowing in the tube that you can see in the upper right hand corner of this video at the 54 second mark. Thanks Louis!!! I blew hard until I heard a bubbling. No new board needed, problem fixed in five minutes. Just make sure you unplug and let it sit and reset itself for a couple minutes before restarting. Also make sure the water is on in case you turned it off (as I did during the diagnostic process). Good luck.

I fixed it, thanks for the valuable info

How do I disconnect the drain hose from the back of the wash machine

Thanks so much for this tip. Worked perfectly.

I am having problems taking the agitator off. I was able to get the bolt off but the bottom piece won't come off. (WTW5640XW0)