Chrysler concorde camshaft position sensor Videos

• 1. How To Replace Camshaft Sensor On A 300M
• 2. How to replace? do it yourself 1999 dodge intrepid cam position sensor replacement part 1 of 3
• 3. How to replace? 1999 dodge intrepid cam position sensor replacement part 2 of 3
• 4. How to replace? 1999 dodge intrepid cam position sensor replacement part 3 of 3
• 5. 2001 dodge intrepid cam sensor again
• 6. 2003 Chrysler Sebring | Mobile Auto Repair Service Testimonial
• 7. 300m cam sensor install.MOV
• 8. Chrysler Cam Sensor Replacement

How To Replace Camshaft Sensor On A 300M

User Comments

Robert Marsh commented on 21 May 2013

Pretty good introduction. But you have loosen all 6 screws from the top, not just the 1st 3 or 4. Plus remove the 2 screws and loosen the other 2 nuts on the engine block in behind the rad. Then look for a third one it is in the centre, and remove the nut and loosen the other nut underneath to remove the metal arm. Then you can raise the plenum a 1/2 inch. Also move the red clip and then use a thin screwdriver to very gently lift the clip near the wiring harness so the old sensor can be removed.

Jon Anderson commented on 04 Nov 2013

When I got the code I about shit a brick. Thought I'd check here to see how difficult it was. WHEW!!!! Thanks Juan! Now I'm really relieved!

Gene Austin commented on 22 Jan 2013

What am I missing? I loosened the six bolts mentioned but nothing was any looser than before

john c. bryant commented on 21 Jun 2013

Hey that worked, there is no reason to take out all the screws. Thank you Juan Carlos

aeonjoey commented on 13 Jan 2014

THANK YOU! got code P0340 and was hella scared it was going to be a lot. you rock!

Charles Weaver commented on 21 Oct 2012

Thanks bro that helped out alot.

Noah Thomas Sr. commented on 11 Jul 2013

THANKS FOR THE INFO

how to replace? do it yourself 1999 dodge intrepid cam position sensor replacement part 1 of 3

User Comments

hellbezzy commented on 10 May 2012

Were is the camshaft sensor on 2001 interpid

how to replace? 1999 dodge intrepid cam position sensor replacement part 2 of 3

User Comments

thumpyls91 commented on 12 Oct 2015

just replaced one today. thx for the vid. the one that i temoved was soaked with oil

djangaunchained commented on 10 Oct 2012

does the crank shaft need to be replaced as well?

JeffreyJames Halvorson commented on 10 Oct 2012

nope it ran great

how to replace? 1999 dodge intrepid cam position sensor replacement part 3 of 3

User Comments

optimusboy1 commented on 14 Nov 2012

thank man this helped me alot with my trep

Jezter49 commented on 05 Dec 2012

nice shot of your arm! haha

2001 dodge intrepid cam sensor again

User Comments

Luke commented on 05 Aug 2014

I have that check engine error too P0601 what is the issue? Is it the Ecm that needs to be changed? Thanks!

tlcbear2 commented on 06 Aug 2014

yes it is the computer that has an issue in  it that it didn't read something right at one time.our car, it has been on 3 years and no trouble other then cam sensor and crank sensor was the only troubles and the coolant housing plastic part was only troubles we had with the car and with that code it still got 27 mpg.so unless its giving you a lot of troubles run it till it don't go anymore.thanks for watching

Cheator40 commented on 22 Jun 2014

I quit having birthdays at 40 LoL

tlcbear2 commented on 22 Jun 2014

i should have lol

bern trailboss commented on 13 Jun 2014

im online bear

bern trailboss commented on 13 Jun 2014

ok

tlcbear2 commented on 13 Jun 2014

i cant get skype to work on the computer i have it on restarting it see if it will work

bern trailboss commented on 13 Jun 2014

ok

tlcbear2 commented on 13 Jun 2014

i will be in about 20 mins finishing a show

2003 Chrysler Sebring | Mobile Auto Repair Service Testimonial

300m cam sensor install.MOV

User Comments

aeonjoey commented on 13 Jan 2014

THANK. you!!!!!! I was wondering about this

Chrysler Cam Sensor Replacement

User Comments

Robert Emmons commented on 10 Jul 2014

Since this sensor also serves as a thrust plate for the Camshaft, shouldn't there be some engine assembly grease or motor oil applied to the surface before reinstalling the sensor?

Airtextech commented on 10 Jul 2014

+Robert Emmons Perfect! Thanks, let us know if you have any issues.Take Care,Mark HicksWells Vehicle Electronics 

Robert Emmons commented on 10 Jul 2014

Thanks. I installed a camshaft sensor on my girlfriend's 2005 Sebring just yesterday, and thanks to your video it was almost too easy. I did dab a bit of engine assembly lube onto the back of the sensor before I installed it. I feel that if there are any parts in contact with moving parts that they should be prelubed to prevent dry contact.

Airtextech commented on 10 Jul 2014

Very interesting question. I have never heard of adding grease to the sensor, however, I feel it would not hurt. Some oil will reach the sensor, apparently the engineers felt this was enough. I like the way you think, thanks for the great comment!Mark HicksAirtex Vehicle Electronics