How to dump xbox 360 nand with lpt Videos

• 1. Xbox 360 nand cable troubleshooting
• 2. How to jtag an Xbox 360 (Cheap and tidy) - Part 2
• 3. Xbox 360 Flash360 v1.0
• 4. Dump da NAND xbox 360
• 5. How To Read Xbox 360 Nand
• 6. NAND-X NANDX Wired Header Install and Reading NAND JTAG Tool
• 7. Reading your NAND with Xell.
• 8. Matrix Xbox 360 USB Nand Flasher Install
• 9. Reading Xbox 360 NAND with Teensy ++ 2.0 in Breadboard

xbox 360 nand cable troubleshooting

How to jtag an Xbox 360 (Cheap and tidy) - Part 2

User Comments

Bob Gogle commented on 14 Feb 2012

is there a later patch for mw2 [after tu7]

Xbox 360 Flash360 v1.0

User Comments

Aaron ModMy Design commented on 28 Jan 2010

Yes you can unban a console doing this, but any console that was banned within the last 6 months is too new and you cannot run Xell on it due to dashboard version, so if your console was banned like last year and the DB was never updated it will work. If you were banned this last fall, it wont work.

MAD8RAD commented on 06 Jun 2011

@atticustheory7 I have a jtagged console that was banned like a year or two ago and was never unbanned. if I use this to unban it wont it get banned again in a matter of hours? and then Its banned forever!?! or will it be permanent? or is there a better way to unban it?

Aaron ModMy Design commented on 19 Jan 2010

Pretty simple has on screen directions. You rename the file you want to flash updflash.bin and place in same directory then follow the on screen instructions the program gives you.

Kevinciio Andress commented on 19 Jan 2010

but did not show how to use... :S

Josh Lehotsky commented on 19 Aug 2011

download?

Dump da NAND xbox 360

User Comments

marcioplacido commented on 15 Sep 2011

Conseguiu???? Vc ligou o xbox se ligar já era

How To Read Xbox 360 Nand

User Comments

angryknome94 commented on 15 Sep 2012

at about 20 seconds in the video you said you could use the nand x or something, i couldent understand sorry. i thought you said the coolrunner which would be great because im going to need that anyway and im trying to keep the cost down. si is the coolrunner what you said? thanks

stopstonedshark commented on 10 Jul 2012

Cheers mate finally found a vid that tells me when to get your nand!! Good work the two dislikes were probably because there american and can't understand the accent =P

XxGLITCH3RSxX commented on 04 Dec 2012

yeah no problem. but yes you would need a motherboard that is jtaggable or one that is rgh able to be able to write xell or ecc to get your cpu key

XxGLITCH3RSxX commented on 15 Sep 2012

no when i said nand x or something i ment the nand x or the jr-programmer or the lpt cable you carn't read the nand with the coolrunner

XxGLITCH3RSxX commented on 10 Jul 2012

hahaha thanks alot mate glad i could help if you need any more help just message me mate thanks

paulc8604 commented on 04 Dec 2012

Thanks for the response . You can only put xell on certain dash boards so i have learned .

paulc8604 commented on 04 Dec 2012

By reading the nand like this do you still get the key off the board ???

XxGLITCH3RSxX commented on 04 Dec 2012

yes but you would need to write xell or ecc to get the cpu key

The404Spartan commented on 20 Sep 2012

:D No back blocks and both are same! hooray!

angryknome94 commented on 17 Sep 2012

thank you for your speedy reply

XxGLITCH3RSxX commented on 17 Sep 2012

np

NAND-X NANDX Wired Header Install and Reading NAND JTAG Tool

User Comments

Big Zeke commented on 19 Oct 2012

Technically you can. However the data on the NAND is HEAVILY encrypted and the only way to decrypt it is if you have your CPU key. To get your CPU key you'll have to JTAG or RGH your Xbox, make a backup of your NAND (Make like 5 backups and check to see if they're good). THen you flash Xell, and Xell will display your CPU key so you can decrypt your NAND image and get your DVD key.

Big Zeke commented on 19 Oct 2012

I'm in the same boat as you. I bricked my RGH system last night so I had to order a NAND-X. However I had made a backup of my NAND before I bricked it and I also have my CPU key as well. So unless you have a NAND image that came from YOUR Xbox 360 or you have your CPU key from YOUR Xbox 360 to build a new NAND image with you're pretty much fucked. You can't just use any NAND image.

WNYConsoleServices commented on 22 Sep 2011

@1200Expert - The NANDX retail kit comes with what are called QSB's (Quick Solder Board). They are pretty easy to install, I may do a tutorial on how to install them one day. First read the NAND with the NANDX, confirm CB, etc, then install the QSB's, then write Xell/Xellous.

scousetomo commented on 16 Feb 2013

bro your videos are cool im just starting my jtag journey read my nand following this video just ordered jtag kit 2 for my falcon 7371 console i normally paid people to do this for me in past thanks for showing me anyone can learn

Dylan i commented on 29 Aug 2012

hey i bricked my jtag a while back and now im trying to fix it. i was told if i buy a nand x and reflash my jtag with the org nand it will work as a jtag again. lol what do u think

Shane James commented on 12 Mar 2015

Can this be done on a jasper latest dashboard as i just got stuck with a load of fake qsb v3's so wanna get on and read my nand without if poss

AdhDgameplay commented on 12 Sep 2012

how did people learn to solder because i want to start doing this and i feel if i mess up with soldering ill be wasting about 70 pounds..

WNYConsoleServices commented on 22 Sep 2011

@pinoyian01 - Not as of today but once the TX CoolRunners are out you will be able to, just need to wait for the software development.

TTGmw4 commented on 28 Jul 2012

Wow. I just got my nand-x yesterday, as well as 3 opus motherboards. This shit is harder and a lot smaller than I thought!

Joe Richards commented on 23 Aug 2012

Can i get my dvd firmware key off the nand? fried my drive trying to flash it and i would like to get a new dvd drive

melicah.david commented on 06 Jan 2012

Great video. Questions, would this be what I need to do to unflagging my xbox 360 console? Could you advice me?

AxelWiresmith commented on 09 Jul 2012

Useless! u didn't use the header. (and that app will get u in trouble if u dont know what ur doing)

Zen Instinct commented on 12 Jul 2012

when you install the NAND X to the motherboard do you have to solder anything else? to it

Max_P commented on 05 Nov 2012

I have a 2008 model xbox, the white one, and i'm wondeing if this will be JTAG-able?

AxelWiresmith commented on 09 Jul 2012

QSB's= Bad news (more RROD's due to varying rates of expansion and contraction)

Maksim Gerasimov commented on 18 May 2013

you can make a detailed video installation XBOX360 Matrix Glitcher Corona?

AxelWiresmith commented on 09 Jul 2012

Give it to a local pro& save ur self the headache my friend :D

KILL3RXXXPAND4GAMING commented on 13 Sep 2013

i have a question. whats the name of ur video for the jtag?

Reading your NAND with Xell.

User Comments

silverDreamMack commented on 04 Oct 2013

i tried key in the ip from my xbox but no menu like in the video

Tobias Solem commented on 30 Dec 2011

How come your file is 600 some megabytes and mine is just 16?

TheLegend2294 commented on 07 May 2012

he has a big block jasper thats why.

Matrix Xbox 360 USB Nand Flasher Install

User Comments

jodie mcbride commented on 13 May 2012

ye you need drivers, mine wouldnt show just beeped you need to downlaod nandpro 20e and go to device manager and you should see memory access with a yellow exclamation mark that is the flasher you need to manually update drivers, browse computer and select the nandpro 20e folder then your flasher wil assign those drivers and it should come up as nand x i did those steps and have made numerous nand dumps with no errors i too sent my first one back if it lights up wen you plug it in it works pal

TairyGreene666 commented on 27 Nov 2011

@TRUESDALEBOY I personally didn't have to install any drivers for it to work. I did have a TIAO nand flasher before this one that I believe needed some drivers so it may be a possibility that those were the ones that were needed. There aren't any explicit instructions that drivers are needed on the Matrix site either though, they just mention that it is compatible with Nandpro 2.0e

910nelson910 commented on 17 Oct 2012

Hey mate, nice tut. but what kind of wires did you use? Can I just use standard singlestring ones from an ethernet cable? :D At least I hope so. And how long should the be? 10-15 cm for the nand flasher. And do you have an Idea how long they should get for the matrix glitcher chip? thx

TairyGreene666 commented on 01 Jun 2012

if you don't have a LPT port you'll either have to find an older PC that does have a LPT port and make the appropriate cable or if you're wanting to use USB you'll have to acquire an interface like the one I use in the video

TRUESDALEBOY commented on 27 Nov 2011

I SENT MINE BACK IM GETTING A NEW ONE SOON, I COULDNT GET IT TO POP UP IN WINDOWS XP, IS THERE ANY DRIVERS I NEED TO INSTALL PRIOR SO THAT THE FLASHER WILL GET RECOGNIZED IN WINDOWS,,ANY HELP WOULD BE NICE THANKS..

Chris Jones commented on 13 Jan 2012

@truesdaleboy i found that if you plug the xbox power in it doesnt show. first plug the usb pwr in and it should show and you do need a device driver for it

Spencer knifes commented on 13 Oct 2012

what is this for? just wondering i mean i know what j tag is but what dose this do and how is this going to help my console? can anyone explain? thanks:D

coheed123 commented on 18 Jul 2012

no. this doesn't replace the glitcher it simply allows you read/write access to your nand which is necessary in creating your rgh/jtag nand image

Brandon Tillman commented on 02 Sep 2012

Yea i caught that in your video the second time. First time it took 1 hour to write then i redid it and it took about 3 minuets. Thanks.

TairyGreene666 commented on 29 Aug 2012

The area where you have to solder all the wires is pretty tight. I recommend single strands from an ethernet cable.

TRUESDALEBOY commented on 07 Nov 2011

the matrix nand programer how did you get it to pop up on the computer, i cant the drivers to load

TairyGreene666 commented on 01 Jun 2012

Reading / writing the nand on an xbox 360. Primarily used in rgh / jtag hacked systems

anyony mous commented on 10 Jan 2015

Where did you get the wires at for the matrix? and what type did you use?

triggers4life commented on 01 Jan 2012

@triggers4life never mind as soon as i un paused you said you did lol

TairyGreene666 commented on 12 Dec 2011

@TheMagnusNeergaard I appreciate the feedback. Thanks.

Magnus Neergaard commented on 12 Dec 2011

Great tut! first one to explain and show it GOOD!!

Brandon Tillman commented on 09 Aug 2012

Does it matter how big or small the wires are?

MrFatmaster1969 commented on 21 Jun 2012

can you use this instead of a rgh chip

Reading Xbox 360 NAND with Teensy ++ 2.0 in Breadboard

User Comments

Tarek Marley commented on 28 Jan 2015

which HEX file did you use for the xbox nand R/W ?